Chimney Top — Caps, Covers & Draft · Anchor Component

Integrated Crown-Cap Unit (Drip-Edge Crown + Cap)

When a crown has already cracked, patching the concrete just buys time before it re-cracks. Our stainless top caps every flue on the chimney and overhangs the crown so water sheds clear of the masonry permanently. Before we sell it we inspect whether the crown needs repair underneath first or whether the cap alone resolves the leak — we document the finding rather than assume.

Specification

What the listing decides

Material: Stainless steel
Store fit: Quote-to-fabricate

How this part is bought

The part follows the finding

No part in this store is a loose transaction. This one links back to the graded inspection that surfaces the need, and across to the install service it belongs to — both performed by the same trained crew.

Upstream

Chimney Inspection

The graded inspection that documents the need for this part before it ships.

Start here

Installed by

Chimney Crown

The install service this component attaches to, fitted to its listing by the same crew.

See the work

Every store quote includes

A fit check — flue size, alloy, venting, and clearances verified against your inspection
Written installed pricing before anything is ordered
Installation to the component's listing by trained technicians
Documentation that closes the finding — so the warranty, your insurer, and the next inspector all see a job done right

Chimney Top — Caps, Covers & Draft

Request a quote

No price is listed — that’s the standard, not a sticker. Installed pricing depends on your flue, alloy, venting, and access, and we confirm it in writing after a fit check. No payment is taken online.

Specify your custom cap

Built to your figures by our fabricator. Spec it here; every measurement is verified on the fit check before a single cut.

Cap style

Size variant

Material

Gauge

Outside measurements

Whole inches plus the fraction, for each side: A (top), B (right), C (bottom), D (left).

A — Topin

B — Rightin

C — Bottomin

D — Leftin

Add 1/2" of clearance to each of the A, B, C and D outside measurements before you submit — Plano fabricates to these exact figures, so the extra half-inch is what lets the finished cap seat over the masonry. I've added the 1/2" clearance to A, B, C and D.

Flue holes

Inside-hole measurements run from the outside edge to the edge of each hole, numbered from the top, then from the left — one pair per flue.

Number of flues

Hole 1

Skirt height

Leg height

Add-ons — available, priced on quote

Rush — faster turnaroundAvailable — priced on quote. (Plano's rush is a 2-business-day fabrication; we confirm the upcharge in writing, never a sticker price online.)Lifetime warrantyAvailable — priced on quote. Plano backs the fabrication for life; we confirm the cost in writing with the rest of the installed quote.

Every figure rides into the quote as your stated spec — confirmed on the measured fit check before fabrication. No price is taken online.

Include professional installationFitted to its listing by the trained crew as Chimney Crown. Leave it on — most parts here are a safety system, not a box you fit on a Saturday.

Pick a preferred window next — we confirm it by phone

(214) 444-8103

Keep browsing

More from the Chimney aisle

Copper Chase Cover (Custom-Fabricated)

We fabricate this chase top in solid copper, fully sloped with standing seams and cut to the exact dimensions of your chase, not a stock size. Copper is the only material we'll spec for a chimney that anchors the roofline: it patinas instead of streaking your siding with rust, and a correctly templated cover never needs a second visit. We take the field measurements ourselves before fabrication, because a cover that's approximately right is a cover that eventually leaks.

View pageQuote

Architectural Multi-Flue Shroud (Decorative)

For a custom home where curb appeal is part of the brief, we build a sheet-metal shroud sized to the chase rather than dropping on a stock cap. Powder-coated steel or copper, corbeled or hip-roofed to match the architecture — we proportion it so it reads correctly from the street, because a capped chimney and a finished chimney are not the same product.

View pageQuote

Powered Draft System (Enervex / Exhausto Inducer + Modulating Control)

This roof-mounted, variable-speed fan uses a sensor control to mechanically draw smoke up a flue that won't draft on its own. We treat it as the last option, not the first: in most cases a height correction, a different cap, or a resized liner fixes the draft fault for less money, so we diagnose before we quote the fan. Where the flue geometry genuinely can't self-draft, we commission this unit to correct the draft, not to mask the underlying defect.

View pageQuote

Everything in Chimney Top — Caps, Covers & Draft

10+

Years

NFPA 211

Standard

CSIA

Certified

< 2hr

Response

Ready when you are

Talk to a CSIA-certified expert today.

Free written quote. Same-week scheduling. 24/7 emergency response when you need it.

Book Free Inspection (214) 444-8103

Licensed & Insured Same-Week Scheduling Written Quote, Always

Emergency

24/7 Response

Active leak, animal in flue, post-fire damage, or smoke event? Real humans on the line 7 AM to 12 AM every day — replies in under 2 minutes. Tech dispatch within 2 hours during business hours, subject to crew availability after-hours.

Emergency line