Spark Arrestor Installation in San Antonio, TX

A spark arrestor is the mesh screen that holds burning embers in, keeping them from escaping the flue and setting the roof or nearby brush alight. A cap is the lid that keeps rain and animals out. The arrestor shields the outside world from the fire within; the cap shields the flue from the weather outside. The two are often combined in a single fitting, which is where the confusion comes from, but the arrestor is specifically the code-sized screen, and we can fit one onto a cap you already own.

No screen over the flue even where a weather cap is present, embers or sparks spotted leaving the chimney top, or an existing arrestor that has rusted through, torn, or sooted solid. A local burn code or an insurer in a fire-prone area can require one as well. Homes near trees, dry brush, or wildfire terrain, and anyone burning wood, stand to gain the most from a functioning screen on every flue.

NFPA 211 requires the screen to be a corrosion-resistant material with openings no smaller than 3/8 inch and no larger than 1/2 inch. The 3/8-inch floor keeps the screen from sooting shut and strangling the draft; the 1/2-inch ceiling keeps embers from getting out. That two-sided limit is what makes an arrestor an engineered fire component rather than a plain cap collar. Some wildfire jurisdictions set stricter rules, so the local requirement controls whenever it's tighter.

Yes — and in these zones the requirement usually runs tighter than the NFPA baseline. Inside a designated fire-hazard or wildland-urban-interface area, one ember that escapes the flue can start a wildfire, which is why local code and a lot of insurers require a compliant arrestor on every solid-fuel flue. Our CSIA-certified techs verify the mesh-and-material rule your jurisdiction enforces, install to that spec, and record the screen size so it's on file for your inspection or insurer.

Embers that clear the flue can drop onto the roof or into nearby brush; over a combustible roof or beside dry vegetation, that's a live ignition point for a roof or wildland fire. The screen is cheap insurance against a costly fire. And an open top with no cap is also letting in the rain and animals a cap is designed to stop, which is why we frequently fit the arrestor and cap together.

Bolt-on and clamp-on screens and arrestor-caps are both available, but the work happens at the flue top on the roof, the mesh has to land inside the code-required size range, and the screen has to seat firmly to the tile or pipe and hold in wind. A screen that's loose or sized wrong fails at the one job it exists for — holding embers in — so we verify both the fit and the mesh size against the code that applies to your property.

A camera-documented inspection first. After long idle years the usual finds are flue blockages from nests and debris, a damper rusted shut, tiles cracked in the 2021 freeze that nobody noticed, and mortar joints quietly past their service life. Sometimes it's a sweep and a damper repair; sometimes it's lining work. The pictures decide. What we won't do is light a test fire in an unknown flue and hope.

Because everything was saturated and nothing here was built for ice. Water sat in joints, crowns, and flue tiles that decades of heat had already micro-cracked, then froze and expanded for days straight. Masonry that had never seen a multi-day hard freeze failed in a single week. A lot of that damage is still out there undiagnosed — it turns up in our flue cameras constantly.

That's the job. San Antonio's palette runs cream to buff, and a gray portland patch on it reads like a bruise. We match the binder — lime for the pre-war work — plus the sand color that gives local mortar its tone, and the joint tooling. On stone repairs we source compatible limestone and set it with the bedding oriented correctly, so it weathers with the wall instead of against it.

Yes — our crews cover San Antonio's 110 ZIP codes across Bexar County, including Alamo Heights line, Stone Oak, Monte Vista, plus the surrounding communities.

We offer same-week scheduling across San Antonio, booked by a real person in under two minutes, 7 AM to midnight every day.

A San Antonio inspection spans some of the oldest masonry in Texas — King William, Monte Vista, Alamo Heights — to vast new-build like Alamo Ranch and Stone Oak, so it documents two dominant findings: historic clay-liner cracking and masonry repointing on the older stock, prefab cap-and-chase condition in the suburbs. Spark Arrestor Installation is part of keeping that local housing stock safe, efficient, and up to code.

Spark Arrestor Installation in San Antonio starts from $250, but the honest number depends on what a craftsman finds on site — we won't quote premium work blind. A CSIA-certified technician inspects the actual condition, then hands you an itemized, transparent written quote tied to the findings and built to one national standard. No teaser pricing, no surprises. Call (214) 444-8103 for a free, no-pressure San Antonio quote.

Yes — we run same-week and emergency spark arrestor installation across San Antonio, scheduled by a real person 7 AM to midnight every day. For an active chimney hazard, call (214) 444-8103 and we prioritize San Antonio dispatch so a craftsman is on it fast.

Our San Antonio crew lives in and works the metro across Bexar County, including Alamo Heights line, Stone Oak, Monte Vista — a certified, local spark arrestor installation team genuinely near you, holding the same national craftsmanship standard on every job, not dispatched cold from another city. Call (214) 444-8103.