Spark Arrestor Installation in Georgetown, TX

A spark arrestor is the mesh screen that holds burning embers in, keeping them from escaping the flue and setting the roof or nearby brush alight. A cap is the lid that keeps rain and animals out. The arrestor shields the outside world from the fire within; the cap shields the flue from the weather outside. The two are often combined in a single fitting, which is where the confusion comes from, but the arrestor is specifically the code-sized screen, and we can fit one onto a cap you already own.

No screen over the flue even where a weather cap is present, embers or sparks spotted leaving the chimney top, or an existing arrestor that has rusted through, torn, or sooted solid. A local burn code or an insurer in a fire-prone area can require one as well. Homes near trees, dry brush, or wildfire terrain, and anyone burning wood, stand to gain the most from a functioning screen on every flue.

NFPA 211 requires the screen to be a corrosion-resistant material with openings no smaller than 3/8 inch and no larger than 1/2 inch. The 3/8-inch floor keeps the screen from sooting shut and strangling the draft; the 1/2-inch ceiling keeps embers from getting out. That two-sided limit is what makes an arrestor an engineered fire component rather than a plain cap collar. Some wildfire jurisdictions set stricter rules, so the local requirement controls whenever it's tighter.

Yes — and in these zones the requirement usually runs tighter than the NFPA baseline. Inside a designated fire-hazard or wildland-urban-interface area, one ember that escapes the flue can start a wildfire, which is why local code and a lot of insurers require a compliant arrestor on every solid-fuel flue. Our CSIA-certified techs verify the mesh-and-material rule your jurisdiction enforces, install to that spec, and record the screen size so it's on file for your inspection or insurer.

Embers that clear the flue can drop onto the roof or into nearby brush; over a combustible roof or beside dry vegetation, that's a live ignition point for a roof or wildland fire. The screen is cheap insurance against a costly fire. And an open top with no cap is also letting in the rain and animals a cap is designed to stop, which is why we frequently fit the arrestor and cap together.

Bolt-on and clamp-on screens and arrestor-caps are both available, but the work happens at the flue top on the roof, the mesh has to land inside the code-required size range, and the screen has to seat firmly to the tile or pipe and hold in wind. A screen that's loose or sized wrong fails at the one job it exists for — holding embers in — so we verify both the fit and the mesh size against the code that applies to your property.

With a camera and a checklist, not a sales pitch. On a house that age we run a full code-level inspection: flue scoped tile by tile, firebox, smoke chamber, crown, joints, and flashing, all photographed into a written report. Victorians here hide surprises — unlined flues, old chimney fires, abandoned stove thimbles behind plaster. Knowing exactly what you own comes first; pricing repairs comes second.

Both, case by case. Weathered limestone with surface loss can often be dressed back or built up with a compatible repair mortar; stone that's cracked through or shedding in sheets gets cut out and replaced with matching material. What we won't do is smear portland cement over soft old stone — it traps moisture and pops the surrounding faces off within a few winters.

Probably less than a salesman would tell you, and more than nothing. Twenty years is when builder-grade crowns crack, chase covers rust at their seams, and caps work loose — small, cheap failures that let water start expensive ones. A photographed inspection sorts it out in about an hour. If everything's sound, the report says exactly that and you're done for the year.

Yes — our crews cover Georgetown's 5 ZIP codes across Williamson County, including Sun City, Historic Square, Berry Creek, plus the surrounding communities.

We offer same-week scheduling across Georgetown, booked by a real person in under two minutes, 7 AM to midnight every day.

Georgetown pairs a beautifully preserved historic square with the sprawling Sun City retirement community and new growth, so the inspection covers Central Texas's oldest-and-newest mix in one report: historic masonry assessed for repointing, modern prefab documented for cap-and-chase condition. Spark Arrestor Installation is part of keeping that local housing stock safe, efficient, and up to code.

Spark Arrestor Installation in Georgetown starts from $250, but the honest number depends on what a craftsman finds on site — we won't quote premium work blind. A CSIA-certified technician inspects the actual condition, then hands you an itemized, transparent written quote tied to the findings and built to one national standard. No teaser pricing, no surprises. Call (214) 444-8103 for a free, no-pressure Georgetown quote.

Yes — we run same-week and emergency spark arrestor installation across Georgetown, scheduled by a real person 7 AM to midnight every day. For an active chimney hazard, call (214) 444-8103 and we prioritize Georgetown dispatch so a craftsman is on it fast.

Our Georgetown crew lives in and works the metro across Williamson County, including Sun City, Historic Square, Berry Creek — a certified, local spark arrestor installation team genuinely near you, holding the same national craftsmanship standard on every job, not dispatched cold from another city. Call (214) 444-8103.