Spark Arrestor Installation in Arlington, TX

A spark arrestor is the mesh screen that holds burning embers in, keeping them from escaping the flue and setting the roof or nearby brush alight. A cap is the lid that keeps rain and animals out. The arrestor shields the outside world from the fire within; the cap shields the flue from the weather outside. The two are often combined in a single fitting, which is where the confusion comes from, but the arrestor is specifically the code-sized screen, and we can fit one onto a cap you already own.

No screen over the flue even where a weather cap is present, embers or sparks spotted leaving the chimney top, or an existing arrestor that has rusted through, torn, or sooted solid. A local burn code or an insurer in a fire-prone area can require one as well. Homes near trees, dry brush, or wildfire terrain, and anyone burning wood, stand to gain the most from a functioning screen on every flue.

NFPA 211 requires the screen to be a corrosion-resistant material with openings no smaller than 3/8 inch and no larger than 1/2 inch. The 3/8-inch floor keeps the screen from sooting shut and strangling the draft; the 1/2-inch ceiling keeps embers from getting out. That two-sided limit is what makes an arrestor an engineered fire component rather than a plain cap collar. Some wildfire jurisdictions set stricter rules, so the local requirement controls whenever it's tighter.

Yes — and in these zones the requirement usually runs tighter than the NFPA baseline. Inside a designated fire-hazard or wildland-urban-interface area, one ember that escapes the flue can start a wildfire, which is why local code and a lot of insurers require a compliant arrestor on every solid-fuel flue. Our CSIA-certified techs verify the mesh-and-material rule your jurisdiction enforces, install to that spec, and record the screen size so it's on file for your inspection or insurer.

Embers that clear the flue can drop onto the roof or into nearby brush; over a combustible roof or beside dry vegetation, that's a live ignition point for a roof or wildland fire. The screen is cheap insurance against a costly fire. And an open top with no cap is also letting in the rain and animals a cap is designed to stop, which is why we frequently fit the arrestor and cap together.

Bolt-on and clamp-on screens and arrestor-caps are both available, but the work happens at the flue top on the roof, the mesh has to land inside the code-required size range, and the screen has to seat firmly to the tile or pipe and hold in wind. A screen that's loose or sized wrong fails at the one job it exists for — holding embers in — so we verify both the fit and the mesh size against the code that applies to your property.

Tract builders in the sixties and seventies often finished chimney tops with a thin smear of mortar instead of a poured concrete crown. Mortar isn't built for that job — it cracks, holds water, and lets freeze-thaw pry the top courses loose. We cast a proper crown with an overhang and drip edge so water sheds past the brick instead of into it. It's the single most common repair we do in Arlington.

Plenty do, some don't. Mid-sixties flues used clay tile, which holds up well unless the tiles cracked or the joints between them eroded — both common after decades of freeze-thaw. A camera inspection settles it in twenty minutes. If the tile's intact, you're done. If not, options range from resurfacing the joints to a stainless liner, and we price both against what the pictures actually show.

Usually, yes. An old cast-iron damper rusted open pulls your heated air up the flue all winter, and one rusted shut makes the fireplace unusable. On most ranch-era chimneys we install a top-sealing damper at the flue exit instead of fighting the original — it doubles as a cap, seals tighter than the factory part ever did, and costs less than people expect.

Yes — our crews cover Arlington's 17 ZIP codes across Tarrant County, including Pantego, Dalworthington Gardens, Viridian, plus the surrounding communities.

We offer same-week scheduling across Arlington, booked by a real person in under two minutes, 7 AM to midnight every day.

Arlington's mid-century brick ranches and the newer Viridian master-planned community sit squarely between Dallas and Fort Worth, so the inspection covers both year-round: freeze-thaw crown cracking is verified on the older stock and prefab cap condition is documented on the newer builds. Spark Arrestor Installation is part of keeping that local housing stock safe, efficient, and up to code.

Spark Arrestor Installation in Arlington starts from $250, but the honest number depends on what a craftsman finds on site — we won't quote premium work blind. A CSIA-certified technician inspects the actual condition, then hands you an itemized, transparent written quote tied to the findings and built to one national standard. No teaser pricing, no surprises. Call (214) 444-8103 for a free, no-pressure Arlington quote.

Yes — we run same-week and emergency spark arrestor installation across Arlington, scheduled by a real person 7 AM to midnight every day. For an active chimney hazard, call (214) 444-8103 and we prioritize Arlington dispatch so a craftsman is on it fast.

Our Arlington crew lives in and works the metro across Tarrant County, including Pantego, Dalworthington Gardens, Viridian — a certified, local spark arrestor installation team genuinely near you, holding the same national craftsmanship standard on every job, not dispatched cold from another city. Call (214) 444-8103.